Will a Nest or ecobee work with Taco zone valves?
Yes, and on a Taco zone valve control the power is already there. Each zone has its own C terminal. The trouble starts on two-wire zones, and on valves wired straight to a small transformer, where the thermostat and the valves share the same 40 VA.
Two answers circulate, and the panel decides between them#
Ask this on a heating forum and you get two replies.
The first says smart thermostats and zone valves do not mix. You hear about dead batteries, "No Power" errors and isolation relays on every zone. That advice comes from real cases. In one 2026 Heating Help thread, an ecobee owner had two Taco 570 valves on a plain 40 VA transformer. A heating pro there advised a separate transformer and isolation relay for the ecobee, or a 75 VA transformer.
The second reply says just connect the C wire. That is right too, when there is a ZVC. Taco prints a C terminal beside R and W on every zone, and lists the thermostats it supports as "most mechanical, battery operated, power-stealing (power-robbing), hardwired and 'Smart' thermostats."
An older Heating Help thread on a ZVC406 shows the gap between them. The owner had six zones of Taco 570-2 valves on two-wire cable. Their new thermostats wanted steady power, and without it "the battery only lasts a few days." The reply was to take 24 V from the panel, and to "add up the power consumed by both the thermostats and zone valves" so the transformers are not overloaded. Both halves of this page are in that answer.
So the answer turns on one question you can check in a minute. Do the thermostat wires land on a Taco control box, or on the valves and a bare transformer?
The terms the answer rests on#
- Zone valve. A valve on one heating loop of a boiler. When a room's thermostat calls for heat, the valve opens and hot water flows to that room's radiators or baseboard. Each zone has its own valve and its own thermostat.
- Zone valve control (ZVC). Taco's box that sits between the thermostats and the valves. Each thermostat wires to it, and it powers the valves and tells the boiler to fire. Taco's current models are the ZVC403-5 to ZVC406-5, for three to six zones.
- R, W and C. The thermostat terminals. R is the 24 volt hot side. W is the call for heat. C, the common wire, is the other side of the transformer. It does not control anything. It only gives the thermostat steady power.
- Power stealing. Also called power robbing. A thermostat with no C wire draws a trickle of power through the heating circuit itself, to charge a battery or run its screen. Nest thermostats do this.
- VA (volt-amperes). The size of a transformer. At 24 V, a 40 VA transformer can supply about 1.67 A in total (40 divided by 24). Everything on it shares that. The same sum sizes a doorbell circuit in video doorbell transformer requirements.
On a Taco ZVC: use the C terminal#
Taco's ZVC406-5 instruction sheet gives three thermostat terminals per zone:
- R: "Hot side of transformer. Connect to R on thermostat."
- W: "Switched R signal from thermostat. Connect to W on thermostat."
- C: "Common side of transformer. Connect to COM on thermostat (optional)."
Taco calls C optional because an old mercury or battery thermostat needs only R and W. A Nest or ecobee is different. Wire all three. Taco's datasheet lists "24 Volt Power Output for Hard Wired Thermostats" as a feature. It says "All thermostat and zone valve connections supply a 24 VAC class 2 output."
The ZVC also keeps the thermostat away from the valve. The thermostat signals the panel on W, and the panel powers the valve from its own output. So the valve's current never runs through the thermostat. That matters for heat motor valves, as the section on bare transformers shows.
The panel's transformer is sized by zone count:
| Taco control | Zones | Transformer |
|---|---|---|
| ZVC403-5 | 3, with priority | 40 VA |
| ZVC404-5 | 4, with priority | 40 VA |
| ZVC405-5 | 5, with priority | 80 VA (two 40 VA) |
| ZVC406-5 | 6, with priority | 80 VA (two 40 VA) |
| ZVC404-R-5, ZVC406-R-5 (reset models) | 4 or 6 | 80 VA |
Each zone valve output is rated 24 VAC, 1 A, and the boiler end switch contacts 24 VAC, 1 A. Taco's sheet recommends 14 to 22 gauge wire for the thermostat runs.
Older or other ZVC models may differ. If yours has no C on the zone, read its own sheet before you buy.
On a ZVC zone with only two wires#
Many old boiler zones have just two conductors to the wall, R and W. This is the "two-wire boiler" case from smart thermostats without a C wire. Here the three brands part ways.
Any power stealing thermostat: Taco's resistor. Taco's troubleshooting section names the problem: "Digital thermostats do not work correctly when connected to a switching relay." Its fix: "Some thermostats are a 'Power Stealing' type which means they are powered by the switching relay with just 2 wires (R & W). A resistor may be needed." The resistor "should be placed between the W & C (common) terminals." If the thermostat maker does not supply one, "a 1000 ohm ½ watt resistor has proven to work with most." The resistor goes in the panel, not in the wall.
Nest: a C wire or the Power Connector. Google says "some zone relay panels don't provide the Nest thermostat with enough power to charge its internal battery." Then it "needs the Nest Power Connector or a common or 'C' wire." Its compatibility page also lists "zone or relay panels" among the hardware that may require a C wire. For the plain Nest Thermostat it goes further: "If you have a Nest Thermostat and a zoned system, you need to connect a C wire or install the Nest Power Connector." On a zoned system, Google says to "install the power connector at the zone controller." It works with 24 VAC only and needs a C terminal on the equipment. A ZVC has one on every zone.
ecobee: a third conductor. ecobee's fix for a missing C is its Power Extender Kit. It works "by combining the Y and G functionality into one wire, freeing up a C wire." A heat-only boiler zone has no Y (cooling) or G (fan) wire, so the kit has nothing to combine. ecobee says its thermostats need a C wire. Taco's resistor is for power stealing thermostats, so it is not ecobee's route either. Find a spare conductor in the wall, or pull new three-wire cable.
Without a ZVC: valves on a bare transformer#
Some systems have no control box. The thermostats wire straight to the valves and a single transformer. Each thermostat then sits in series with its valve. Its power and the valve's power come from the same 40 VA. This is where the forum trouble comes from.
What the valves draw, from each maker's sheet:
| Valve | Type | Rated draw at 24 V | Share of a 40 VA transformer (1.67 A) |
|---|---|---|---|
| Taco 570 series | Heat motor | 0.9 A | About 54 percent each |
| Taco Zone Sentry (Z050C2-1) | Motor with a capacitor | 0.48 A while charging, 0.06 A once on | 29 percent charging, 4 percent on |
| Honeywell V8043E | Motor | 0.30 A (7.2 VA maximum) | 18 percent |
Taco 570 heat motor valves. A heater warms a wax element, and the wax pushes the valve open. Taco's brochure says power to the heater is cut "in the fully open mode." As the piston eases back, the contacts close and heat it again. "This slight back and forth motion is repeated as long as the thermostat contact is closed." A thermostat that steals power through that circuit keeps losing it. One heating pro in the 2026 Heating Help thread says some smart thermostats report "No Power" for this reason, and recommends an isolation relay.
Taco Zone Sentry. Taco's sheet sets a limit: "Do not use more than 12 zone valves per 40VA transformer." It adds: "Some power robbing thermostats may cause a reduction of the number of valves possible per 40VA transformer." It also says "always use the resistor provided by the thermostat manufacturer with the Zone Sentry." The valve's LED tells you when power runs short. A slow blink, once every 5 seconds, means the capacitor is taking too long to charge. Taco's listed fixes include a larger transformer, fewer valves, and "Use a different thermostat."
Honeywell V8043E. At 0.30 A it is the lightest of the three. Honeywell does not address smart thermostats in the sheet read here.
The fix on a bare transformer is the C wire from the transformer's common side, if the power allows it. When it does not, the choices the Heating Help pros give are a bigger transformer, or an isolation relay with its own transformer for the thermostat. That relay idea is the same one used for a smart thermostat on a millivolt fireplace. A ZVC solves the series problem, since the panel gives each zone its own R and C and powers the valve itself. It does not add power: Taco's three and four zone panels also run on 40 VA.
Worked through: two 570 zones, then a ZVC#
Here is one case walked through the published figures. Nobody tested it. Take the setup from the 2026 Heating Help thread: two zones of Taco 570 valves on one 40 VA transformer, and an owner who wants an ecobee on one zone.
The valves alone. Each 570 draws 0.9 A at 24 V, or 21.6 VA. Both zones calling at once draw 1.8 A, or 43.2 VA. A 40 VA transformer is rated for 1.67 A. On paper the valves already ask for more than it is rated to give, before any thermostat is added. That is why the pros in the thread said a separate transformer or a 75 VA one.
Add the ecobee. Its C wire would land on that same transformer. ecobee's pages read here do not publish the thermostat's draw, so this page does not add a number. The point stands without one: there is no spare power to share.
The same house with Zone Sentry valves. Two charging at once draw 0.96 A. Once open they hold at 0.12 A together. That leaves room on a 40 VA transformer, and Taco's own limit is 12 valves. The thermostat would still eat into that limit, per Taco's warning.
The same house with a ZVC403-5. The two 570s now run from the panel's outputs, each rated 1 A. The ecobee wires R, W and C to its zone terminals. Its call for heat goes to the panel, not through a heat motor, so the heater cycling no longer cuts its power. The panel's transformer is still 40 VA, though. Taco's sheets read here do not say how many 570s one panel runs at once, so this case does not claim the budget is solved. If the cable has only two wires, the owner needs a spare conductor or new cable, since ecobee's kit needs Y and G.
Which fix, by setup#
| Your setup | What to do | Source |
|---|---|---|
| Taco ZVC, three or more wires to the thermostat | Wire R, W and C to that zone's terminals | Taco ZVC406-5 sheet |
| Taco ZVC, two wires, Nest | C wire, or the Nest Power Connector at the zone controller | Google Nest zoned systems and Power Connector pages |
| Taco ZVC, two wires, a power stealing thermostat | The maker's resistor, or a 1000 ohm 1/2 W resistor from W to C at the panel | Taco ZVC406-5 sheet |
| Taco ZVC, two wires, ecobee | A spare or new conductor for C; the Power Extender Kit needs Y and G | ecobee Power Extender Kit page |
| Zone Sentry valves on a bare transformer | C from the transformer; no more than 12 valves per 40 VA, fewer with power robbing thermostats; only the thermostat maker's resistor | Taco Zone Sentry sheet |
| Taco 570 valves on a bare transformer | Count 0.9 A per valve against 1.67 A; add a transformer or an isolation relay, or a ZVC to take the thermostat out of the valve circuit | Taco 570 data; Heating Help pros |
Where this page stops#
This page covers Taco's current ZVC controls, Taco 570 and Zone Sentry valves, and the Honeywell V8043E, from their own sheets, plus Google's and ecobee's pages, as read in November 2026. Three limits matter most. First, Taco's resistor text speaks of a "switching relay" and says the resistor "has proven to work with most" thermostats, not all. Second, neither Google nor ecobee publishes a thermostat's VA draw on the pages read, so this page cannot say how many thermostats one transformer will carry. Third, ecobee's own zone valve support pages did not load, so this page makes no claim about their wording. Other brands' zone panels (Honeywell, Argo, Caleffi) and steam systems were not read. Line voltage heat is a different problem, covered in smart thermostats for baseboard heaters. The panel and the boiler run on 120 V, and Taco's sheet says wiring "must be made in accordance with all applicable electrical codes." Turn off the power at the panel before touching it, and call a heating pro if the cable or the panel is not what this page describes. If you rent, the boiler is the landlord's, as a smart home for renters explains.
After the wiring#
A Nest or ecobee on each zone runs that zone on its own. Google says Nest thermostats in one home "don't share temperature schedules," so each learns the zone it controls. Before you rely on one in a boiler house, check what it does when the internet goes down. The wider wiring and Matter picture is in smart thermostats and the C wire.
Does a Nest thermostat work with Taco zone valves?
Yes, but give it steady power. Google says some zone panels "don't provide the Nest thermostat with enough power to charge its internal battery," and then a C wire or the Nest Power Connector is needed. On a Taco ZVC, wire the Nest's C to the zone's C terminal, or fit the Power Connector at the zone controller.
Can I put an ecobee on a two-wire boiler zone?
Not on two wires alone. ecobee's Power Extender Kit works by combining the Y and G wires, and a heat-only zone has neither. Use a spare conductor in the cable as C, or pull new three-wire cable to the zone's R, W and C terminals.
What is the resistor for on a Taco zone valve control?
Taco says some power stealing thermostats, powered by just R and W, may not work properly on its controls. A resistor between the zone's W and C terminals may be needed. If the thermostat maker does not supply one, Taco says a 1000 ohm, 1/2 watt resistor "has proven to work with most."
Where is the C terminal on a Taco ZVC?
On each zone's thermostat terminal block, beside R and W. Taco labels it "Common side of transformer. Connect to COM on thermostat (optional)." It is optional for old thermostats. A Nest or ecobee should use it.
How many zone valves can a 40 VA transformer run?
It depends on the valve. A 40 VA transformer gives about 1.67 A at 24 V. A Taco 570 heat motor valve draws 0.9 A. Taco limits Zone Sentry valves to 12 per 40 VA, and warns that power robbing thermostats can lower that number.
Primary sources
Specification and vendor documentation we checked while writing this page. Where a claim depends on firmware behaviour rather than a published spec, the page says so inline.
- Taco, ZVC406-5 Zone Valve Control instruction sheet 102-575 (February 2021)
- Taco, Next Generation Zone Valve Control datasheet, catalog 100-164 (October 2024)
- Taco, Zone Sentry zone valve instruction sheet 102-410 (Z050C2-1, November 2014)
- Taco, Heat Motor Zone Valves brochure and submittal data 100-3.2 (570 series, June 2013)
- Honeywell, V8043A,E,F 5000 Series zone valves, form 95C-10932 (InspectApedia copy)
- Google Nest Help, how Nest thermostats work with zoned systems
- Google Nest Help, Nest thermostat compatibility
- Google Nest Help, Nest Power Connector
- ecobee, Power Extender Kit
- Heating Help, wiring digital thermostats and Taco ZVC406
- Heating Help, ecobee thermostat with Taco 570 zone valves (February 2026)