What smart switch works for a whole house fan?
A motor-rated on/off switch or relay, wired past the fan maker's own control. QuietCool says its RF control cannot connect to a smart home. The fans draw little, so one speed is easy. Two speeds need two relays that can never close together, and a dimmer is never the answer.
Two answers circulate, and the wiring decides between them#
People who ask this get two replies.
The first says just add a smart plug or a hub that copies the fan's remote. QuietCool's own guide answers that for its RF kit. Asked whether the RF control can connect to Alexa, Google Home or Apple HomeKit, it says: "No, in the current configuration the RF Control cannot connect to a smart home system." It adds that other systems can translate RF signals, "but they have not been tested and may not work reliably."
The second reply says any smart switch will do, since the fan is small. That is half right. The amps are small, but a two-speed fan has two power leads, one per speed, and a single switch can only feed one. And a light dimmer is a different device from a switch, as the next section shows.
So the answer turns on how the fan is wired, not on how big it is.
The terms the answer rests on#
- Whole house fan. A large fan in the ceiling or attic that pulls cooler outdoor air in through open windows and pushes warm indoor air out through the attic. QuietCool's guide says it works "anytime it is cooler outside than the inside of your home."
- Speed lead. A two-speed fan motor has a separate power wire for each speed. Power on the high lead runs it on high, and power on the low lead runs it on low. The fan maker's control picks one lead at a time.
- Relay. A switch worked by a small electrical signal instead of a finger. A smart relay is a relay with a radio. It sits in the wall box or near the fan, and your hub tells it when to close. Wi-Fi models talk to your router; Z-Wave and Zigbee models need a hub, as which radio for which job explains.
- Motor rating. The largest motor a switch's maker says it can turn on and off, printed in horsepower (HP), apart from its amp rating. A standard motor table converts it to amps at 115 V: 1/6 HP is 4.4 A, 1/2 HP is 9.8 A, 3/4 HP is 13.8 A and 1 HP is 16 A.
- Interlock. A rule that stops two relays from closing at the same time. On a two-speed fan it stops power reaching both speed leads at once.
- Dimmer. A control that cuts part of each power cycle to dim a light. It is made for lamps, not motors.
Why a dimmer or fan speed control is the wrong part#
A dimmer is out. Inovelli's Blue Series dimmer manual is plain: "Not rated for inductive loads or fans." It warns that dimming a fan or motor "could cause damage to the dimmer, the load bearing device, or both." The same advice ran through the SmartThings threads. In the 2021 thread, one reply warned that a light dimmer on a motor can "create a fire hazard." In the 2017 thread, a reply said "do NOT use a ceiling fan switch," because "Whole-house fans are a different type of motor."
A ceiling fan speed control does not fit either. The smart ones read for choosing a smart switch for a ceiling fan are rated 1.5 A to 2.5 A, and the CL-3100 pulls 2.58 A on high. QuietCool also never asks for a variable control. Its ES-3100 sheet recommends an "8 Hour Electronic Timer (IT-30070) and HI-LOW-OFF Switch (IT-35000)." Those are step controls: off, low or high.
What the fans draw#
These figures come from QuietCool's own spec sheets. Every model here runs on 120 V.
| Fan | Speeds | Power | Amps (as listed) | QuietCool's recommended control |
|---|---|---|---|---|
| CL-1500 | 1 | 117 W | 1.21 A | IT-36002 RF Wireless Control Kit |
| CL-3100 | 2 | 299 W high, 256 W low | 2.58 A high, 2.20 A low | IT-36002 RF Wireless Control Kit |
| ES-3100 | 2 | 285 W high, 80.8 W low | Not listed | 8 hour timer IT-30070 and HI-LOW-OFF switch IT-35000 |
The ES-3100 sheet gives watts but no amps. Watts divided by volts gives a floor: 285 W at 120 V is about 2.4 A. A motor draws a little more current than that. The CL-3100 shows how much: 299 W against a listed 2.58 A.
QuietCool's own RF hub, the IT-RFHUB-01, is rated far above any of these. Its garage fan manual lists it as "Motor load: 1HP, 735W (Max)" at 120 V. The control was built with plenty of room, and a smart replacement can be too.
The smart switches and relays, against those amps#
Each rating is as its maker publishes it, read in November 2026. The amps column uses the motor table above.
| Control | Radio | Motor rating | Motor amps at 115 V | Neutral |
|---|---|---|---|---|
| Kasa HS200 | Wi-Fi | 1/6 HP | 4.4 A | Required |
| Zooz ZEN17 relay (NO outputs) | Z-Wave | 1/2 hp, 20 A | 9.8 A | Runs on its own 12 to 24 V supply or USB-C |
| Leviton D215S | Wi-Fi | 3/4 HP | 13.8 A | Required |
| Zooz ZEN75 Heavy Duty | Z-Wave | 1 HP at 120 V | 16 A | Required |
What the table settles:
- Even the smallest rating clears one fan. The HS200's 4.4 A is above the CL-3100's 2.58 A on high, and well above the CL-1500's 1.21 A.
- Zooz names whole house fans for the ZEN75. It lists "whole house fans" up to 1 HP at 120 V. It also says the switch gives "simple on/off control without speed adjustments."
- None of the wall switches can run two speeds. Each has one load output. Only the ZEN17, with two relays, covers both leads.
How the horsepower and amp figures relate on a smart switch, and why the amp figure on the front is the wrong one for a motor, is covered in garbage disposal on a smart switch.
One speed: a motor-rated switch on the high lead#
If you only want the fan on or off, one switch does it. Wire it to the speed you want, which is usually high. The poster in the 2017 SmartThings thread had a QuietCool ES-2250 and planned to run it on high only. They later ran it from a smart outlet with a whole house fan app.
The key step is to take the maker's control out of the path. Do not put a smart switch in front of the QuietCool RF hub and expect it to start the fan. The RM guide says that "In order for the fan to run, a Timer selection MUST be made" on the RF switch. Nothing in the guide says the hub starts the fan by itself when power returns. So the smart switch has to feed the fan's speed lead directly.
Smart switches and the neutral wire shows how to check the box for a neutral. Every wall switch in the table needs one.
Two speeds: two relays that cannot close together#
This is the case most guides skip. A HI-LOW-OFF switch has one position at a time, so it can never feed both leads. Two separate smart switches have no such limit. A scene, a schedule or a voice command could turn both on.
The Zooz ZEN17 solves this with a setting. A Zooz support article on The Smartest House gives the wiring for a QuietCool fan:
- Connect the fan's high-speed wire to the R1 NO terminal and the low-speed wire to the R2 NO terminal. NO means normally open: the circuit is off until the relay closes.
- Connect the fan's 120 V power to the C terminals of both R1 and R2.
- If you keep a two-speed wall switch, wire its high side to S1 and its low side to S2, so the switch still works as an input.
- Set parameter 24 to 1. Zooz calls it DC motor mode. Its settings page says it will "Sync R1 and R2 together to prevent them from being activated at the same time."
- Use the R1 child device in your hub for high, and R2 for low.
Two more settings matter. Parameter 1 decides what the relays do after a power cut. The default, 1, has them "remember and restore status". Setting it to 0 leaves both off. Also note that the ZEN17 does not run on 120 V: Zooz says it takes "12-24 V or a USB C plug," and no power supply comes in the box. That supply needs room too, so read box depth and fill before you plan to fit both in a wall box.
This is the same pattern as a pump start relay on a smart sprinkler controller: a small smart device closes a contact rated for the load, instead of carrying the job itself. The ZEN17 is a Z-Wave device, so it needs a hub such as Home Assistant.
Worked through: one CL-3100, then two#
Here is one case, walked through the published figures. Take a house with a QuietCool CL-3100 on the RF kit, whose owner wants it on a schedule.
One speed. The fan draws 2.58 A on high. A Kasa HS200 is rated 1/6 HP, or 4.4 A. That leaves room, so an HS200 on the high lead, with the RF hub taken out, gives on and off from an app.
Both speeds. Now suppose the owner also wants low for overnight, which QuietCool's guide suggests: turn the fan "on low after desired cooling occurs and let it run throughout the night." The HS200 has one output, so it cannot do this. A ZEN17 can. High goes on R1 and low on R2, with parameter 24 set to 1. Its 1/2 hp rating is 9.8 A, against 2.58 A.
A second fan. QuietCool's guide recommends a fan in each bedroom. Suppose the owner wires two CL-3100s to the same control. On high the two draw 5.16 A together. That is over the HS200's 4.4 A, so the HS200 is out. It is still under the ZEN17's 9.8 A and the D215S's 13.8 A. Three fans would draw 7.74 A, still under 9.8 A.
The timer. QuietCool's RF kits, in the two guides read, have a timer of up to 12 hours, and the fan will not run without a timer setting. The smart setup has none unless you add it. So the owner sets an automatic off in the hub, so the fan never runs all day by mistake. Automations people do not turn off explains why a rule with a built-in end ages better than one that relies on someone remembering.
Other brands#
AirScape. AirScape once published a local web interface for its Gen 2 controls. A 2014 post gave an HTTP command for speed up, speed down, timer and off. That post now carries an update: "This option is currently NOT available. A new Network Controller is in development." So there is no published local route into an AirScape fan today, and you should not plan around one.
Others. The 2021 SmartThings thread was about a Lomanco fan with a solid-state variable speed control. That thread ended without a way to keep variable speed in a smart setup. This page read no Lomanco, Tamarack or other fan maker's documents, so it makes no claim about them.
Which control, by fan#
| Your fan | What to fit | Why |
|---|---|---|
| One-speed fan, such as a CL-1500 | A motor-rated smart on/off switch | 1.21 A is under even the HS200's 4.4 A |
| Two-speed fan, one speed wanted | A motor-rated switch on the high lead | The CL-3100's 2.58 A on high fits a 1/6 HP rating |
| Two-speed fan, both speeds wanted | Zooz ZEN17, R1 high, R2 low, parameter 24 set to 1 | Zooz's mode stops both relays closing together |
| Several fans on one control | Add the amps; use the ZEN17 (9.8 A), D215S (13.8 A) or ZEN75 (16 A) | Two CL-3100s on high already pass 4.4 A |
| QuietCool on its RF kit | Replace the hub with one of the above | QuietCool says the RF control cannot join a smart home |
| AirScape | Nothing published | The local API is "currently NOT available" |
| Any whole house fan | Never a dimmer or ceiling fan speed control | Dimmers are not rated for fans; fan controls top out at 2.5 A |
Where this page stops#
This page covers 120 V QuietCool fans from their own spec sheets and guides, four smart controls, and the Zooz wiring guide, as read in November 2026. It covers no Tamarack fans and no 240 V fans, and no other fan maker's documents were read. QuietCool's RM WHF-4.0 has three speed wires and a different motor, and the Zooz guide was written for a two-speed fan, so this page does not give relay wiring for it. Nothing read here says how a fan's dampers behave under a smart control. Nothing read here covers a link to a fire alarm or smoke detector either, so this page makes no claim about either one. QuietCool's guide has you open windows first, then turn the fans on. A schedule cannot do that for you, so a contact sensor on a window is worth adding to the rule. This is mains wiring. QuietCool's RM guide says "Wiring should be done by an experienced electrician," and local codes may require a permit. A Wi-Fi switch such as the HS200 or D215S also needs your network to take commands, as what still works when the internet goes down explains, and local versus cloud control covers where its schedule actually runs.
Can I connect a QuietCool whole house fan to Alexa or Google Home?
Not through its RF control. QuietCool's guide says "No, in the current configuration the RF Control cannot connect to a smart home system." To use a voice assistant, replace the RF hub with a motor-rated smart switch or relay, wired straight to the fan's speed leads.
Can I use a dimmer on a whole house fan?
No. A light dimmer is not made for motors. Inovelli's dimmer manual says it is "Not rated for inductive loads or fans." Smart ceiling fan speed controls are rated 1.5 A to 2.5 A, under a CL-3100's 2.58 A on high. Use an on/off switch or relay with a motor rating.
What smart switch can run a two-speed whole house fan?
A single wall switch runs one speed only. For both, use two relays that cannot close at once. A Zooz ZEN17 does this: high goes on R1, low on R2, and parameter 24 set to 1 stops both relays closing together.
How many amps does a whole house fan draw?
Less than most people expect. QuietCool lists 1.21 A for its CL-1500, and 2.58 A on high and 2.20 A on low for its CL-3100. Its ES-3100 uses 285 W on high, about 2.4 A or a little more. Check your fan's own sheet.
Can I put a smart switch in front of the QuietCool RF hub?
It is not a reliable way to start the fan. QuietCool says a timer selection must be made on the RF switch for the fan to run. The guide does not say the hub restarts the fan when power returns. Wire the smart switch or relay to the fan's speed lead instead.
Primary sources
Specification and vendor documentation we checked while writing this page. Where a claim depends on firmware behaviour rather than a published spec, the page says so inline.
- QuietCool, RM WHF-4.0 roof mount whole house fan owner's guide (2020)
- QuietCool, GA ES-1500 garage fan installation manual with IT-RFHUB-01 specifications
- QuietCool, CL-3100 specifications (Lowe's document)
- QuietCool, CL-1500 specifications
- QuietCool, ES-3100 specifications (Home Depot document)
- The Smartest House (Zooz), How to use the ZEN17 Universal Relay to control a whole house fan
- Zooz, ZEN17 Universal Relay product page
- Zooz, ZEN17 Universal Relay advanced settings
- Zooz, ZEN75 Heavy Duty Switch recommended loads
- Zooz, ZEN75 Heavy Duty Switch FAQs
- Kasa, Smart Wi-Fi Light Switch HS200 product page
- Leviton, Decora Smart Wi-Fi 2nd Gen Switch D215S
- Warren del Caribe, single phase motor full load amps table (Acme Electric figures)
- Inovelli, Blue Series dimmer switch manual (VZM31-SN)
- AirScape, Gen 2 Controls API (June 2014, with later update note)
- SmartThings Community, smart switch for attic/whole house fan (September 2021)
- SmartThings Community, controlling whole house fan, outlet or switch (2017)